CHECK LOWEST PRICES , BEST DISCOUNT and COMPARE PARE PRICES ABOUT Delta 36-L552 5 HP Unisaw, 52-Inch Fence
table saw mobile base SAVE SHOP-new & used...
Delta 36-L552 5 HP Unisaw, 52-Inch Fence
table saw mobile base
best deals price products
Delta 36-L552 5 HP Unisaw, 52-Inch Fence
table saw mobile base for TOP PRODUCT FOR BUY & SALE OF THE YEAR :
  |
Delta 36-L552 5 HP Unisaw, 52-Inch Fence Product Brand : Delta Model : 36-L552 |
|
table saw mobile base
Special for Best Deals Shopping for
Customer Review :
Delta mod# 36-L552 5 HP uni saw 52" fence : Delta 36-L552 5 HP Unisaw, 52-Inch Fence
I live in the suburbs , the saw arrived as stated and the truck had a lift gate to unload it as well as a small hydraulic cart to move it where I wanted it. Great Its very heavy about 600 lbs with the packaging including 2 palletts. It was wrapped very well , some card board was scuffed , I opened it and found no damaged. The delivering carrier had to remove the long fence (it was packaged vertically with the rest of the saw) they had to remove it to get it in the truck. All is well.
This is a five (5) horsepower saw.
It required a 40 amp circuit breaker, so before you buy it you MUST have a 40 amp circuit with 10 gauge wiring. It has a plug on the saw. The circuit is 40 amp 220 volt. I thought I had the correct set up but NO. I had 220 volt with a "20 amp" circuit so I had to hire a electrician to wire it up. Luckily it was about 30 feet (in my shop with easy access to install the wiring.
The saw is very smooth , powerful and fairly quiet.
I bought the mobile base with it, very sturdy. MAKE SURE YOU GET THE CORRECT MOBILE BASE. I would not buy the base again because the saw is so heavy , I don't think I'll move it.
You MUST level the saw to the base then level the saw and base to the world.
Take your time in installing the wings. There is a special way to install them , call Delta tech support, to get them level.
The fence and table and all parts were very time consuming. I had to remove some of parts and reinstall them before I was satisfied that it was on the "Co-plane)
It required a lot of blocking etc to get the saw up tilting towards the back then put blocks under it to get the mobile base under it. It can be done with a little enginering with blocks and levers. It took a lot of time to set it up , after you get it level and co planed it is great. Take your time go slow and you will be rewarded with a good cutting saw with no bumps on the fence.
The fence table was not exactly the same width as the saw so I had a gap between it and my new home built outfeed table.
I recommend the saw. The sliding fence works very smooth - no bumps like my old one. BUT you must get it co planed level. OK I've said that enough.
The blade was with .001 degree of vertical. I hope I sad that right. It was so minute I did not correct it to be 100% vertical. The fence and blade was parall witht the slots. The mitre needed a little tweaking. Take your time and get it right.
I have a Sears shop vac ( the biggest one they make) and it does a respectable job sucking the saw dust.
Mumbles
deltadrillpresstablesawmobilelaserbas.blogspot.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON SERVICES LLC. THIS CONTENT IS PROVIDED ‘AS IS’ AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME.
buy-Bicycle Seat Cover-Sport Shop Best 4 Buy Carpet Burgundy Home Garden
No comments:
Post a Comment